Saturday 22 September 2012

Nocturne Brain Seltzer Classic

Info from the manufacturer about the original:

NEED a BRAIN for your BLONDE?

If you want the missing link between your filtertron'd Hollowbody and vintage bassman amp, namely the RE-301 space echo, to get that blonde ol' stray cat sound.. I built this Pre-amp to have that particular catalyst and the mojo of what a 301's input circuit does to the gretsch guitar and blonde fender..

(I have redesigned the circuit to also work great with strats, teles, LP's and even Dynasonic and p-90 loaded guitars)

This is indeed a pre-amp, not an "FX" box, its not a boost or drive box. It causes the guitar to be heard better by the normal channel of a blonde 63' bassman..(the Dyno Brain and Atomic brain also work well with a wide variety of tube amps) I've spent yrs trying to make this happen, I'm no engineer, just a singer-guitarist with one sound in my ears I had to have... so I'm making em' 1 at a time!








BUY A KIT

72 comments:

  1. This is weird.. I just built one of these last night from a different layout I found online. I had a bunch of 1458's and was looking for small projects. I will rebuild it tonight with your layout. what a coincidence. lol

    ReplyDelete
    Replies
    1. Very spooky, especially seeing as the original uses a LM741 single opamp and I only used the double because it seems more people are stocked up on them now, and they're really no more expensive for the common ones.

      Delete
    2. Your right.. The one I have had LM741.. I really need to remember parts. I am just working on getting my stock up on parts and I am tired of seeing LM 1N 2N OHM lol

      Delete
    3. Tell me about it. It's been a sickness in me for a couple of years now and you wouldn't believe what I've hoarded in that time. You'd laugh if you knew how many resistors I've managed to stash! :o)

      Delete
  2. Hi Mark!

    Did you make the vero from my schematic at fsb.org?

    Cheers,
    Chris aka G5120fx aka Dork

    ReplyDelete
    Replies
    1. Ha ha ignore my last comment, I was talking about the other layout I did yesterday! DOH! Yes I used the scheme that electromatic showed on his layout.

      Delete
    2. Hi Mark. On said schematic on FSB, there is a 0.1uf cap on the tone control from lugs 3 to 1 and a 100pf cap on the in lug to the wiper. Are they not needed?

      Delete
    3. Yes they are needed, but I hate mounting components on pots so they're on the board.

      Delete
  3. I´ll try your vero in the next days....
    I found a gutshot of a atomic brain on ebay, seems there´s not much difference. Would be cool if we could work out how it works. i updated the thread yesterday with a pic.

    Thanks for the layout!

    ReplyDelete

  4. It´s verified. But i have the same strange problem, I had with the other vero before. There´s some noise when the effect is engaged.

    Maybe you could tell me what thois could be:
    http://www.2shared.com/audio/m3v8vW7e/brain.html

    ReplyDelete
    Replies
    1. Hmmm weird. It sounds like noise you can sometimes get from oscillators but there is no oscillator in this. Do you get the noise if you run it off a battery and mains?

      Thanks for verifying!

      Delete
  5. Hi again!

    Ok, i found the problem. I boxed it up and the noise is gone?! Maybe it was a Grounding issues?

    So, verified ;)

    ReplyDelete
    Replies
    1. Hi G5120fx. How does this version with the LM1458 sound compared with the 741?

      Delete
    2. Intersil list the LM1458 (or CA1458 for their version) as the dual version of the LM741 so they should be pretty close.

      Delete
  6. I used a ts4558 i had laying around, sounds pretty close too. i already ordered a lm1458, so i´ll report when i got it!

    ReplyDelete
  7. Hi Paul.D1 on the original traced schematic is a 4001.

    ReplyDelete
  8. This comment has been removed by the author.

    ReplyDelete
  9. Anyone know how this differs from the new Dyno Brain circuit, which was apparently modified to accommodate more guitar pickups, and increase gain?

    ReplyDelete
  10. Where does the neg side of the led connect to? I connected mine to the top left corner of the 3pdt then to the positive side of the power jack and all I'm getting is a loud buzz when plugged in.

    ReplyDelete
    Replies
    1. Yes that is correct, but the positive side needs to go to "LED+" on the board. If you connect it directly to the supply without a limiting resistor the LED will burn out in a couple of seconds.

      Delete
  11. gotcha, it had to be something wrong with the offboard wiring. I put all the jacks and switches in the box first then soldered the leads to them. I've since taken everything out and will wire everything up first.

    -If i dont have a 2.2K around, could I use something similar in instead?
    -Also, could you take a look at the "wiring for dummies" picture I made from your layout to verify i'm doing this correctly? I think I'm still doing the LED wrong. Here is the link:

    http://i1150.photobucket.com/albums/o617/tremellow814/nocturneoffboard.jpg

    ReplyDelete
    Replies
    1. The LED resistor is already on the board, that layout pic assumes there isn't one on the board. So just take the LED+ connection directly to the LED anode as you have shown in your diagram, but leave out the 2K2 and connected wire completely.

      Delete
  12. This comment has been removed by the author.

    ReplyDelete
    Replies
    1. Thanks Mark, you sir are a gentleman and a scholar.

      I believe my picture is now correct?

      http://i1150.photobucket.com/albums/o617/tremellow814/nocturne-offboard.jpg

      And from now on, I'll assume the resistor in the offboard diagram isn't needed if there is a connection to LED in the vero layout

      Delete
    2. Not quite, you need to remove the wire to the DC socket.

      Delete
  13. Hello IvIark, thanks a lot for the Layout. I've ordered the parts and will try it immediately.

    But do you know whats different in the circuit of the dyna brain? Or even better: the atomic brain?

    The Seltzer Classic Circuit is pretty basic. So the changes shouldn't be dramatic. What do you think?

    Thanks and have a nice day.

    ReplyDelete
  14. Good question... I'm curious what the difference is as well.
    Anyone?

    ReplyDelete
    Replies
    1. Interesting question indeed.. But i can't find any schematics other than this. You guys find any?
      +m

      Delete
    2. I've been searching as well as I don't have a blonde fender amp unfortunately, anyone got any ideas for the Dyna or the Atomic?

      Delete
  15. Hello,
    Which is the correct way to wiring the input and the tone in this circuit ?

    http://www.2shared.com/document/MF3U3_B9/wiring_1.html
    http://www.2shared.com/document/YDbqxsuL/wiring_2.html

    Cheers

    ReplyDelete
    Replies
    1. 1 is right, the input wire has to daisy chain to volume 3 from the board. Or you can take 2 wires from the lug of the switch, or 2 wires from Volume 3. Whichever is easiest for your build.

      Delete
  16. Hi everybody ! Could you send me the correct complete layout with the pots and stomp switch wiring! Please ! I just bought the kit and the circuit is ready but don t work at all . I know i ve made a mistake on grounds wiring pr in stomp switch wiring but don t know where!

    ReplyDelete
  17. I must percise the pot wiring is ok ( i refered to a picture above ) so in fact i think i m wrong on jack input and output winring and on the stomp

    ReplyDelete
  18. Hi,
    yesterday i built the the pre-amp and it gives a nice little bit more twang. Unfortunatly the tone control does not work, do you have an idea what could be te issue ?

    Thanks

    ReplyDelete
  19. It seems the tone control or "Bass Cut" has little effect for most people. I chose to just omit it. I got my layout form FreeStompb**s.org. It is is a great circuit though and I pretty much leave it on all the time.
    You will need to experiment with pedal placement though, it can act weird with other pedals.

    ReplyDelete
  20. This comment has been removed by the author.

    ReplyDelete
  21. If you want to build your own pcb.
    My small contribution to the project:

    http://www.absul.com.br/limbo/bsnpcb.png

    ReplyDelete
  22. Hi guys,

    I'm new in DIY and also blond !! I started to buid this preamp but i can't find where to plug the jacks connectors, the minus point of the power supply. Could you please help me or just send a picture of the finished oui product ?

    Thanks in advance for your help and best wishes for 2014

    Fred

    ReplyDelete
    Replies
    1. This should clear it up a bit Frederick. http://tagboardeffects.blogspot.com/2012/02/offboard-wiring.html

      Delete
    2. Hi,

      Thanks so much for this fast and very clear answer.

      I hope I can test my new stomp soon !

      Have a nice sunday

      Fred

      Delete
    3. Hi again,

      I'm a bit disappointed, I thought I followed well the instructions but when I test it I just have a hum but no any signal. The led is working but with a quite low light. The switch seems to work but this is all what I can get.

      You will find here after a link to 2 pictures, perhaps you can spend some minutes to check and help me. I hope !

      http://www.heberger-image.fr/data/images/51258_image.jpg
      http://www.heberger-image.fr/images/88694_image.jpg.html

      Thanks in advance.

      Fred

      Delete
    4. It looks like you may have wired up one of the jack sockets incorrectly. The wires appear to be on the 'switched' side, i.e. they are disconnected when the jack is plugged in.

      Delete
  23. Hi,

    Thanks for your answer, both jacks were connected the opposite way. So now I have a signal but when the led is on it's like bypassed. I mean that the signal is like the dry one and the volume potentiometer does nothing. When the led is off, I have no more signal just an oscillation noise. Both, volume and tone potentiometers does nothing at all.

    Do you think the switch is connected opposite way ?

    Is this preamp true bypass or not ? Because when I switch off the power supply I have the dry signal.

    I checked many times the drawing, the cut on the board and so on but found no problem. That's strange.

    Thanks to all of you for your help. If I find a solution I'll keep you informed but as brand new in this field I'm not so confident.

    See you

    ReplyDelete
  24. Hello:
    I need the schematic, it not found in Google...
    Thanks!

    ReplyDelete
    Replies
    1. You'll find 99% of the schematics for layouts on here at freestompboxes. Check out the thread at that site.

      Delete
  25. Hello, after giving another try to this circuit I have been experimenting with the tone stack and I find that a capacitor of 10n instead of 100n makes the high pass effect audible. Also, having the nocturne place after a buffer makes the tone work better. With 100n or more the tone control is completely useless for any of my guitars. 10n or less works fine

    ReplyDelete
    Replies
    1. Thanks for the info MIguel, it should be useful for anyone else who might need to mod it to make it work with their gear.

      Delete
  26. I built this as my first stripboard project. I had a few small problems but it's now working and souns great! At first I didn't get anything from the tone control, so I took Miguel's advice and swapped the 100n for 10n. Now I get a nice twang with the tone fully down,
    thanks IvIark!

    ReplyDelete
  27. can someone help me out when i built the circuit and plugged it all in it just crackles

    ReplyDelete
  28. Hey guys, not exactly new to building pedals, but I tend to take long breaks and forget a ton and have to relearn stuff every time I start back up...can some one help me with the capacitors? I know the round ones are radials, but on this schematic in particular, does the orange oval mean its a disc and the maroon oval mean its a drop? and if so, why can't I find a 100n cap anywhere? Do I have to shop for it as a .0001u or something? just need some help sourcing please lol thanks to any replies in advance.

    ReplyDelete
    Replies
    1. It's the value of the cap thats important, not the material it's made of. In this case the 100pF cap is the small orange oval. These are small and easy to fit into a 2.5mill span. The 100n cap (maroon) can be a metal film type or a poly box type. Again it doesn't matter which...but a Poly box cap would physically fit into that space better as they are usually 5mill pitch and low profile.

      The metal film types are a lot bulkier. They will still work but they won't fit in as snug as a poly box.

      Try searching for polyester box caps and metal film caps to see the differences. An for future reference...1uF = 1000nF = 1,000,000pF. So a 100n cap would be 0.1uF

      Delete
  29. How does the switch and Pots wire into this ? sorry for such newbie questions but i picked this as a starter build into vero boards but im stumped on the connections to vol, and tone and switch

    ReplyDelete
    Replies
    1. hi there!
      for the switch follow this
      http://tagboardeffects.blogspot.gr/2012/02/offboard-wiring.html

      for the pots, you can do this:
      with a small link connect lugs 1&2 on the tone pot, and from those take one more wire(double link on lug1 or 2) and sent it to where tone1&2 is on the board. take a wire from where vol2 is on the board, sent it to vol pot lug2 and with an other wire-double link on that lug2 go to tone 3. from vol pot lug1 take a wire to any ground spot you want. the green input wire must go to vol pot lug3 and from that same lug 3 you get your input wire going to stompswitch with an other wire..
      you MUST read this too
      http://tagboardeffects.blogspot.gr/2012/04/vero-build-guide.html
      hope i helped.
      good luck.

      Delete
    2. Thank you , so much. I will read the vero build guide now. This site is so huge i havent known where to start. maybe i jumped in the a little deep.

      Delete
    3. any time buddy. this is not just a great sounding build, but it's also not that complicated of a build. definitely a great one to start off with.

      while there is so much info here, everyone starts at the same point, and there's a learning curve. the more you build the more you'll learn, and you'll start to want to find out more info so you'll read more, and things fall into place. just don't forget to ask for help if you need it, cause sometimes it can get really frustrating. would rather see someone else get into building and enjoy it then just give up.

      Delete
  30. This comment has been removed by the author.

    ReplyDelete
  31. This comment has been removed by the author.

    ReplyDelete
  32. Hi,
    Just built this one and trying to troubleshoot. Bypass works, but no sound when engaged. However when I remove the IC (from its socket) I get a low effect signal at about 50% volume, also can be controlled but the volume pot. IC is orientated correctly and believe is working. Need to get a replacement to rule that out, but wondering if there might be something else.

    Any help much appreciated ..Cheers

    https://ibb.co/nrDAbR
    https://ibb.co/mAYMi6

    ReplyDelete
    Replies
    1. Voltages on the IC pins 1-4 and 8?
      +m

      Delete
    2. thanks for your reply. I've not taken readings before (very new to this) but I believe it is below, power supply is sending 9.38V

      1 - 4.42
      2- 4.42
      3- 4.42
      4 - 0
      8 - 8.83

      Delete
  33. This comment has been removed by the author.

    ReplyDelete
  34. This comment has been removed by the author.

    ReplyDelete
  35. This comment has been removed by the author.

    ReplyDelete
  36. Hello, This is my first build. I picked it because of the simple board layout. When I engage the effect there is less volume from the amp then when not engaged and it doesn’t sound very good. I have a real dyno brain so I know what it is suppose to do and this just isn’t right. The only thing I could think of is I used a LM1458N as that is all there was at Tayda. Is this different from a LM1458? Can you think of anything else that might be wrong? Thanks

    ReplyDelete
    Replies
    1. The chips I had were bad, got new chips from a different supplier and it works.

      Delete
  37. soo...anyone done the Atomic Brain with the Abby mode yet?

    ReplyDelete